Reasons Your Fiat 500 Key Fob Won't Work

A key fob from fiat key duplication (funsilo.date) 500 is a great way to open the doors and start the car. There are many reasons the fob could stop working. This could be due to a dead coin-battery, water damage, problems with receiver modules, as well as interference.

This listing is for an NEW replacement fiat key fob Fiat Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local automotive locksmiths). Includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob doesn't function is the battery is dead. Key fobs of today have limited operating range and must be within a few inches of your vehicle to work. If you're far from your vehicle and push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the coin cell battery (Part number CR2032) with a brand new one from a reliable brand such as Panasonic, Duracell, or Energizer. They are available at the local hardware store or online.

After you've replaced the battery in the coin cell It is possible to test it by standing next to your fiat 500 abarth key fob replacement 500 and pressing the buttons. The car should blink its parking lights, and the key fob will operate the lock and unlock switches.

If your key fob isn't working after replacing the battery, there may be water damage that hinders it from interacting with the module in your vehicle. Water damage can happen in many ways, such as the simple splash or submerging the key fob into saltwater at the beach. If you believe your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this doesn't work, your fob is likely to need to be reset by an experienced auto locksmith or by the dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water out of the chip's electronic circuit, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short and eventually fail. It's not the best idea to soak the fob in water however, don't give it up if you accidentally drop it in water or fail to take it out of your pants pocket.

First take the battery off the fob. Clean the electronic chip using isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Then, test the fob to see if it works. If the key doesn't work, it might need to be changed. This is usually handled by an auto locksmith or dealer.

If your key is older and has not been programmed for your car then you'll need to replace it completely. This is a simple procedure that can be handled by a professional locksmith for automotive use. The locksmith will need the key cut to match your car's ignition. They'll also have to reprogram the fob to the car's system. It's a simple and cost-effective procedure that is usually completed in the next day.

Receiver Module Issues

One of the main reasons your 500 key fob could stop functioning is that it's out of range. The remote has a maximum range of 30 feet, so in the event that you are far from your vehicle it won't respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.

If your fob does not work after you replace the battery for the coin, also known as a "button", "watch" or "button" or "button", it could be due to an issue with the circuit board inside. Reprogramming the fob usually resolves this issue. You can find the procedure for most vehicles on YouTube or in the owner's manual.

It's possible that you need to replace the metal clips that hold the coin battery. If they lose tension it can prevent the battery from being seated properly and can cause your remote to malfunction.

In rare cases the fob might become disconnected from your vehicle due to software issues or hardware issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances they might need to reinstall the software on your body control module too.

Interference

In addition to a dead battery on a coin, the key fob may not be receiving or transmitting the signal due to interference. This could happen if the key fob is close to radio transmitters (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob could not work because of a weak connection to the buttons water damage or damage to the internal chips.

If the key fob been unable to function for a while out of the blue or after trying everything you can at home to fix it e.g. You may have a faulty 500 receiver module after you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module, which lost key to car fiat is located under the dashboard, receives radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's on-board system including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Then reconnect the battery. This will remove any remaining electrical charge and restart the car's computers, which could allow you to get your key fob working again. If the issue continues it is recommended that you consult an expert technician. They will be able diagnose the root cause of any problems.